UNI-FLEXX FRONT PART FOR XL 150

Precise planning is crucial in concrete construction, because concrete does not forgive mistakes – until now. With the Uni-Flexx you can add spots, loudspeakers or other built-in devices in ceiling slabs that have already been cast. The required core drilling is much smaller and therefore significantly cheaper than usal. This increases your flexibility on site and saves you a lot of time and money. See for yourself!

AND ACTION!

The clever trick in concrete construction

To the Product

Thanks to the clever design, the Uni-Flexx only requires a small core drilling to retrofit spots or other built-in devices in ceiling slabs. A drill hole of 74 mm is sufficient to make the installation opening. This can be done by any fitter, for example with the Primo Schnellläufer.

74 mm bore hole
68 mm installation opening
10 – 50 mm installation depth (can be shortend in stages)

After the front part has been fixed, the installation housing XL 150 is attached. You now benefit from all advantages that the XL-Series offers. Among other things, conduit entry without tools, absolute concrete-tightness, integrated conduit grip and optimal thermal management.

Further information can be taken from the data sheets.

DATA SHEETS

PRIMO UNI-FLEXX

ALL ADVANTAGES AT A GLANCE

SIMPLE INSTALLATION

IN A FEW STEPS

74 mm Bohrloch wird in Betondecke eingebracht

Drill a 74 mm hole in the ceiling slab. The commercially available Primo Schnellläufer is suitable for this.

Primo Uni-Flexx mit abgetrennten Installationssegmenten.

If necessary, cut off installation segments to adapt the installation depth to the ceiling thickness.

Primo Uni-Flexx steckt im Bohrloch einer Betondecke.

Insert the Uni-Flexx into the drill hole.

Löcher zur Befestigung des Primo Uni-Flexx werden in Betondecke gebohrt.

Drill holes through the mounting brackets..

Primo Uni-Flexx wird mit Schlagdübeln auf Betondecke befestigt.

…and attach the Uni-Flexx front part to the ceiling with knock-in anchors.

Primo Einbaugehäuse über dem Primo Uni-Flexx mit normalem und optionalem Trafotunnel.

Attach installation housing XL 150. The universal tunnel can optionally be attached to expand the installation space.

Primo Einbaugehäuse mit installierten Kabeln und Rohren auf der Betondecke.

Open the membrane with a cutter knife to insert cables and conduits. The system is immediately absolutely concrete-tight and ensures reliable strain relief.

Decke mit Primo Einbaugehäuse wird betoniert.

Attach the reinforcement and concrete the ceiling.

Einbauleuchte und Trafo wird in die Öffnung des Primo Uni-Flexx gesteckt.

Connect built-in lights and other built-in devices from below and insert them into the 68 mm installation opening.

Innenansicht von Primo Uni-Flexx mit eingebautem Spot.

Suitable for clips with rubber coating and metal clips with expanding tabs.

Complete installation.

Primo Einbaugehäuse und Uni-Flexx eingegossen in Beton.

Done!

COMPONENT PARTS FOR

THE UNI-FLEXX

Installation Housing XL 150

Due to its design, the installation housing XL 150 – in combination with the Uni-Flexx – is ideal for the installation of built-in devices in visible roof constructions. The insulation remains intact and thus energy efficiency is still guaranteed. Thanks to the membrane entries, the XL 150 convinces with quick and easy installation and offers many other advantages such as integrated conduit grip and reliable stain relief. For this outstanding quality, functionality and innovation the XL-Series was rewarded with the prestigious Red Dot Award.

Primo Einbaugehäuse mit Uni-Flexx und Trafotunnel eingebaut in Betondecke.

UNIVERSAL TUNNEL

The universal tunnel creates additional installation space, which is suitable for larger electronic components. It can be attached to the Primo installation housings XL 150, XL 200 und XL 250.