THROUGHLY THOUGHT THROUGH
TO EVERY CORNER
THROUGHLY THOUGHT THROUGH
TO EVERY CORNER
TIME-SAVING, CLEVER AND USABLE ANYWHERE
Absolutely concrete-tight, mounted in seconds and with numerous possible applications. With the new XL-Series installation housings, Primo has developed all-rounders that are perfect for mounting all special installation housings – from luminaires to loudspeakers to other built-in components. The probably greatest advantage for precast factories: The XL 200 and the XL 250 can be attached with a magnet. This saves a lot of time in production and also delivers a high-quality product. The perfect material for your perfect prefabricated slab.
AND ACTION!
THE XL-SERIES INSTALLATION HOUSINGS
With two different sizes and individual installation openings the XL-Series is a flexibel all-rounder that can be used for the installation of all kinds of loudspeakers, luminaires and built-in devices.
Beside the classic attachement with glue and a mineral fiber board the installation housings can be positioned on the formwork with an integrated magnet in the universal board – either manually or automatically in the precast factory. In addition to a higher quality of the final product, bothersome removal of glue residue is no longer necessary. On top of that are the magnets recyclable and therefor more environmentally friendly compared to conventional methods. The magnets remain in the installation housings and the electrician can simply remove them on the construction site in order to return them to the cycle via the magnet recycling.
All information about the Primo magnet recycling
With at least 25 entries each, all variants of the XL-Series offer sufficient space for cables or conduits in sizes from M9 to M40. The maximum installation depth of built-in devices in the XL-Series is 110 mm. The halogen-free polypropylene multi-talents are heat-resistant from -5 °C to 100 °C and can also be used outdoors.
Further technical information can bei taken from the data sheets:
SIMPLE INSTALLATION
IN A FEW STEPS
Universal board with an integrated magnet.
Precise positioning on the formwork.
The installation housing can still be rotated by 360°, imprecisions can still be easily corrected.
XL plate magazine with XL front parts is picked up by robot.
Front parts a positioned automatically on the formwork.
Reinforcement and cross-irons are being installed.
Installation housing is being placed.
Glue is being applied on the mineral fiber board.
Installation housing is being positioned precisley.
Reinforcement is being installed.
Prefabricated slab is being delivered and assembled.
Open the membrane with a cutter knife.
Absolute concrete-tight openings due to membrane technology.
No shortening of conduits due the conduit stop.
The combination entries offer space for cables and conduits (M9 – M40) without tools.
Cables and conduits can be pulled into the installation housing even before concreting.
High impact resistance due to the innovative design.
Minor editing on the construction site.
Remove magnets and recycle them to save ressources and the environment.
Mill individual openings with a carbide cutter.
Install any desired built-in device.
ACCESSORIES FOR
THE XL-SERIES
EXTENSION RING
The XL 200 extension ring can be pushed onto the corresponding installation housing to create more installation space by increasing the height. Extension rings can be connected to one another until the desired installation depth is achieved. The push-fit system ensures a fast and a stable connection. With the help of the extension rings, the Installation housings can also be retrofitted, for example in precast slabs.
TUNNEL
With the universal tunnel, additional connection space can be gained, which is suitable, for example, for larger electronic components. It can be pushed onto the Primo XL 200 and XL 250 installation housings.
FRONt PARTS FOR INDIVIDUAL SOLUTIONS
Various front parts are available for the Primo XL 200 and XL 250 installation housings. The universal board with an integrated magnet and the mineral fiber board (145 – 195 mm) allow individual openings. The XL-Series is thus suitable for every conceivable area of application. As a further option, square (68 – 75 mm) or round (68 – 180 mm) front parts can be used for individual cut-outs.
FURTHER SOLUTIONS FOR
CONCRETE INSTALLATION IN PRECAST FACTORIES
Frequently asked questions
FAQ
Was sagt der Putzer zu den Deckeln für das Thermodosensystem?
Wir hoffen er sagt: WILL ICH! Laut VOB/C sind gemäß DIN 18299 die Gewerke zu schützen. Dies bedeutet, dass der Putzer dafür sorgen muss, dass die gesetzten UP-Dosen sauber bleiben. Mit beiden Deckeln des Thermodosensystems wird das im Handumdrehen möglich. Die optimale Putzdicke von 10 mm wird immer erreicht.
Die Dose wird schnell gefunden, Wandschäden, die entstehen, wenn der Elektriker nach der Dose suchen muss, entfallen.
Putzer und Elektroinstallateur werden Freunde.
Warum entfällt das Bohren beim Geräteträger?
Die Montagefläche des Primo Geräteträgers wurde mit diversen Öffnungen konstruiert. Somit können Leuchten und weitere Geräte mit Schrauben bis 4 mm Durchmesser am Geräteträger ohne Bohren und Dübel-Setzen zeit- und kostensparend montiert werden.
Wie öffne ich den Geräteträger?
Der Geräteträger wird durch die Putzfedern auch nach dem Verputzen leicht gefunden. Wir haben eine Sollbruchstelle vorgesehen, sodass der Deckel vorsichtig mit dem Hammer geöffnet werden kann. Alternativ kann der Deckel auch mit einer 35er Lochsäge geöffnet werden.
Geräteträger braucht doch kein Mensch, oder?
Mit dem „eingegipsten Dübel“ von Primo hat der Bohrer erstmal Pause. Denn der Elektroinstallateur von heute schraubt die Montageplatte der Leuchten direkt am Geräteträger fest – ganz ohne Bohren und Dübel setzen!
Natürlich nicht zu vergessen: durch die sorgfältige Konstruktion der Thermodosen werden alle Kabel und Rohre im hinteren Teil der Dose eingeführt. Bei der Montage von Leuchten werden Kabel oder Rohre also garantiert nicht beschädigt.
Schützt der Geräteträger das Doseninnere vor Putz?
Ja, auf jeden Fall! Durch die Putzfedern wird die Dose aber dennoch schnell und ohne Wandbeschädigungen gefunden. Der Geräteträger eignet sich für 35 mm Öffnungen.
Für Standardöffnungen von 60 mm empfehlen wir den Universalputzdeckel für das Primo Thermodosensystem. Der praktische Helfer wird auf die Dose gesetzt und nach dem Putzen einfach eingedrückt, oder mit einer 68 mm Lochsäge entfernt.
Das Ergebnis? Saubere Putzkante. Putzschäden waren gestern!
Ich habe eine UP-Dose mit 60er Öffnung gesetzt. Die ist für den Leuchtensockel zu groß. Was kann ich machen?
Der Kunde möchte plötzlich Lampen mit extra schmalem Leuchtensockel? Kein Problem mit dem Primo Geräteträger. Der Deckel wird auf der eingesetzten Unterputzdose mit zwei Schrauben festgeschraubt, die Wand verputzt und der schmale Leuchtensockel direkt auf der Montagefläche des Geräteträgers befestigt.
WE ARE THERE
FOR YOU
Hotline
+49 8638 88559-200
Ask our experts
To the Primo expert chat
E-Mail
info@primo-gmbh.com